DeutschLow voltage
Power supplies for voltages up to 600 Volt at high precision
Here you can find a overview about our power supplies for your low voltage / high current application.
With an extensive packet of options we can tune this standard power supplies to your application.
LNG - Series
Linear control low-voltage laboratory power supply
- linear control low-voltage laboratory
power supply in bench case - output power up to 200 Watt
- output voltage up to 350 Volt
- output current up to 6 Ampere
- residual ripple < 0,1% pp
- stability < 0,1% over 8h
- setting of output voltage with ten-turn potentiometer
- setting of output current with ten-turn potentiometer
- 3-digit digital displays for voltage
and current - analog interface
- sustained short-circuit resistant
LNG-datasheet (PDF) PTN - Series
Double-stabilised linear control low-voltage power supplies
- Double-stabilised linear control power supply with high precision
- output power up to 5000 Watt (higher performance see PTN3p)
- output voltage up to 600 Volt
- output current up to 200 Ampere (higher currents see PTN3p)
- residual ripple < 0,01% pp, (up to 0,001% as PTNhp)
- stability < 0,01% over 8h
- setting of output voltage with ten-turn potentiometer
- setting of output current with ten-turn potentiometer
- 3.5-digit digital displays for voltage
and current, analog displays on request - analogue interface
- digital interface avalible as option
- ustained short-circuit resistant
- sense-connection
PTN-datasheet (PDF) PTN3p - Series
Double-stabilised linear control low-voltage power supplies
- Double-stabilised linear control power supply with high precision
- output current up to 5.000 Ampere
- output voltage up to 600 Volt
(for higher voltage see PHN Seriess) - residual ripple < 0,01% pp, (up to 0,001% as PTNhp)
- stability < 0,01% over 8h
- setting of output voltage with ten-turn potentiometer
- setting of output current with ten-turn potentiometer
- 3.5-digit digital displays for voltage
and current, analogue displays on request - analog interface
- digital interface avalible as option
- ustained short-circuit resistant
- sense-connection
- 19" rack on columns or casters
- customized versions are possible, e.g. for 2-quadrants operation
PTN3p-datasheet (PDF) PTNhp - Series
High precision double-stabilised linear control low-voltage power supplies
- Double-stabilised linear control power
supply with highest precision - output current up to 5.000 Ampere
- output voltage up to 600 Volt
(for higher voltage see PHN Seriess) - residual ripple < 0,001% pp
- stability < 0,001% over 8h
- setting of output voltage with ten-turn potentiometer
- setting of output current with ten-turn potentiometer
- 3.5-digit digital displays for voltage
and current, 4.5digit displays on request - analog interface
- digital interface avalible as option
- ustained short-circuit resistant
- sense-connection
PTNhp-datasheet (PDF) PTNer - Series
High Performance Power Supplies with Active Energy Recovery
- Robust power unit based on the PTN3p series with "Heinzinger Energy Recovery"
- Integrated energy recovery that converts energy returning from the consumer back into network voltage and is fed back into the supply network
- Very good dynamic behaviour
- Minimal threshold between power units and energy recovery mode with intelligent detection of the operating mode of the consumer
- Comprehensive digital and analogue control methods
- Power unit function with integrated option "Battery characteristic curves" for recreating the behaviour of a battery
- Suited for non-stop operation, extremely reliable
- Modular design
- Galvanic separation of the consumer in energy recovery mode
- Power unit available in water-cooled version
PTNer-datasheet (PDF) PNY - Series
SCR controlled low voltage power supplies
- output current up to 10.000 Ampere
- output voltage up to 600 Volt
(for higher voltage see PHY Seriess) - residual ripple < 0,1% pp,
- stability < 0,1% over 8h
- setting of output voltage with ten-turn potentiometer
- setting of output current with ten-turn potentiometer
- 3.5-digit digital displays for voltage
and current, analogue displays on request - analog interface
- digital interface avalible as option
- ustained short-circuit resistant
- sense-connection
- 19" rack on columns or casters
- customized versions are possible, e.g. for 2-quadrants operation
PNY-datasheet (PDF) PCU - Series
High Precision Power Supplies for Magnet Applications
- Extremly precise power supply for magnets
- Modular system, parallel operation to increase output power possible
- Zero-Voltage-Switching Technology
- Maximum accuracy and stability (<10ppm/8h)
- Temperature coefficient <10ppm
- Optimum ratio between power density/accuracy
- DCCT current measurement
- Programmable current ramp function
- 2-part LCD display with text indicator
- Analog (0...10V) and digital interface (RS422)
- Controller configuration/load balancing possible
- Last setting memory
- Air colling (optional water cooling)
- Triggereingang für Mess-Signal
- Trigger input for measurements signals
- Output short-circuit and open-circuit proof
- Pole-reversal unit for switching polarity optional
- Various voltage/current combinations
- Customer-specific variants
PCU-datasheet (PDF) GEN-Series, Distribution - Line
1U/2U switch mode power supplies up to 3.300W
- compact 1U or 2U rack, 19" (or 1/2 19" at 750W), for system integration
- output performance 750, 1.500, 3.300W
- output voltage up to 600 Volt
- output current up to 400 Ampere
- residual ripple < 0,1% ss
- stability < 0,1% über 8h
- setting of output voltage and current with coarse/fine adjustment
- digital displays, separat for voltage and current
- analog interface 0...5V / 0...10V
- digital interface RS232 / RS485
- system solutions and customized configurations on request
GEN-datasheet (PDF)