[Translate to English:] Ausgangsstrom up to 600 A
Output current
[Translate to English:] Ausgangsspannung up to 1,000 V
Output voltage
[Translate to English:] Leistung up to 250 kW
Output power up to 250 kW
[Translate to English:] Mehrkanalbetrieb Up to 2 channels
Multichannel operation mode
    • highly dynamic DC source and load with energy recovery to the mains
    • also 2 channel system available, upgrade possible at later time also
    • operation, control and parameterization by touch screen or via an automation interface
    • galvanic isolation by resonance converter
    • floating output with short-circuit protection
    • sense function for stabilization of voltage drops in the load line
    • continuous transition between source and load operation
    • voltage, current or power control
    • adjustable internal resistance regulation
    • configurable output regulation
    • high-resolution measurement system
    • water cooled

    Your personal contact
    Artur Gunko

    +49 80 31 - 24 58 - 63



    DC sources / sinks for testing rigs safeguard product quality

    Realistic, high-quality tests with different operating states and exacting requirements

    DC sources / sinks for testing rigs are a core component in the development, quality assurance and EOL (end-of-line) testing for batteries and power electronics in the domain of e-mobility. The dynamic properties, the combination of high control accuracy, low residual ripple, and a large output voltage range are crucial. This means that, with the DC sources / sinks for testing rigs, users have the ability to efficiently cover high-voltage applications as well as 48-Volt applications with just one testing rig energy system. Various software packages enable the DC sources / sinks for testing rigs to be used as battery simulators or battery testers, allowing the following applications to be supported, for example:

    • Battery simulation
    • Battery testing
    • Inverter and DC engine test for EV & HEV
    • Testing of charging stations
    • DC Sources / Sinks for Testing Rigs
    • Testing of power electronics (DC / DC converters)
    • DC load for fuel cells

    Heinzinger DC sources / sinks for testing rigs in the ERS series allow practical and realistic testing with excellent quality. As a key core component of all kinds of testing rigs, in research and development or from quality assurance to end-of-line testing, they offer their users long-term investment security. The return of unused energy into the supply network also ensures that the DC sources / sinks for testing rigs deliver excellent energy efficiency and low operating costs. 

    By using a twin-channel device, two items being tested can be supplied with power simultaneously, opening up a variety of different operating options for the DC sources / sinks for testing rigs. This means that, through “energy balancing”, all of the energy can circulate between the test items across both output channels. This produces fewer losses than if individual devices were being used, and only the test item's losses from the grid have to be tracked. As a result, even with lower installed mains power, tests can be carried out with a high power demand. Another advantage of using a twin-channel device is the opportunity to increase power for one output channel. We will be happy to advise you other possible uses for a multi-channel system

    DC sources / sinks for testing rigs for battery simulation

    The devices in the ERS series are designed especially for battery simulation. The following features of the DC sources / sinks for testing rigs are important:

    • table output voltage even with pulse currents
    • Simulation of the battery’s internal resistance
    • Parameterizable battery models
    • Dynamic rated value change up to 1 kHz
    • Continuous transition between source and sink mode
    • Switchable insulation monitor function

    Battery tests and verification of high-voltage batteries

    For testing rigs used to test and verify high-voltage batteries from the EV and HEV sector, the DC sources / sinks must meet special requirements. These include, among others, the following criteria:

    • Currentless connection of the battery
    • Charging and discharging mode with automatic switch-off
    • Discharging of the output capacities on switch-off
    • Rated value monitoring and monitoring of the system limits
    • Automatic toggling of control types
    • Switchable insulation monitor function  

    Tell us by phone us on +49 80 31 2458 0 or e-mail us at info(at)heinzinger(dot)de what requirements you have regarding the power supply for your testing rig. We will be happy to advise you on DC sources / sinks in the ERS series and recommend the ideal device for you.

    Send your request now

    Would you like to know more about power supplies from Heinzinger?

    More power supplies with energy recovery from Heinzinger

    Bidirectional Power Supply for voltages 60V - 2,000V
    ERS Compact

    ERS Compact is the ideal solution for your 48-Volt applications

    ERS Compact
    High voltage power supply for 1,200kW

    Battery simulation with ERS BIC for maximum outputs up to 1200 kW